Rampage Power Lift Ramps

The Rampage Motorcycle Lift is the EASIEST and SAFEST way for ONE PERSON to load one or two motorcycles into the back of a pickup truck or trailer.

The Rampage Power Lift Ramp, easily and safely loads and unloads your motorcycle. From the ground to the back of your vehicle, one person can safely load and unload their bike whileh never getting on the motorcycle by pushing a button on a remote control switch. The Rampage Power Lift Ramp allows for storage and still allows you to pull a boat or trailer. The unique configuration fits into most full-size or mid-size pick up truck beds and has the ability to be installed in very short truck beds such as Chevy Avalanche or Honda Ridgeline.

The lift will extend past the end of the bed and carry the load safely without damaging the tailgate. The Rampage Motorcycle Lift is not a permanent modification, it consists of a modular, 3 piece construction for easy installation and removal by one person in minutes!

Rampage Power Lift Ramps includes quality features like an extremely strong, structural steel design capable of loading 1000 poiunds. The wheels and rollers are industrieal grade nylon and there are no bearings to grease or maintain. The carriage tracks are slotted to allow for rain water, dirt and debris. The 2500 LB capacity winch with a 5000 LB capacity strap operates on a 12 volt DC system.

The Rampage Power Lift Ramp is a simple, reliable design that is very easy to operate and requires very little maintenance.

Click on the above images to enlarge. Click Here to see additional pictures

• You can carry one or two Motorcycles in your truck bed
• Pull a boat or travel trailer while carrying two Motorcycles
• Install the rack in minutes by yourself.
• Remove the rack from your truck in minutes
• No Trailer to Store
• No Insurance
• No 55 MPH in the slow lane
• No Trailer Registration

• Handles the largest Motorcycles with ease.
• Fast and Simple - One Person Operation
• Lifts the Motorcycle from FLAT on the ground
• Full lift cycle time is under 1 minute
• Strong Structural Steel 3 Piece Frame
• One Person can set up and remove from the truck easily
• 2500 LB Ramsey Winch with safety brake
• 12 Ft wired remote control (Wireless Remote Control also Available)
• Two units can fit in a standard width bed
• Fits almost any truck or trailer
• Easy Installation with 3 bolts
• Removes in just a few minutes
• Fully powder coated to protect against rust or chipping

• Carrying Capacity: 1000 LBS.
• Width: 23 1/2" (Two units will fit between the wheel wells of a standard truck)
• Length: 95 inches (Fits in an 8 ft truck bed with the tailgate closed)
• Weight: Approximately 330 LBS. (Separates into 3 manageable pieces)
• Winch: 2500 LB Ramsey Winch with integrated safety brake
• Winch Strap: UV treated, 5000 pound rated, polyester webbing
• Winch Remote Control: 12 ft remote which can be disconnected and stored in the truck
  • Wireless Remote Control Available for an addtional Charge
• Tire Cradle: 6 inches wide and sits 7 inches above the truck bed
• Bed Attachment: Rivet Nut type fasteners that are installed in the bed and do not require attachment to the frame. Fasteners are installed from the top and does not require access from the bottom of the bed.
• Bed Height: Tested for truck bed heights of up to 39". For higher beds, please inquire. We offer to test and certify other heights as required
• Electrical Connection: #6 AWG cables with quick disconnect

• Rampage Lift capable of lifting 1000 LBS
• Low friction skids for easy removal
• Four tie down bars
• One Carrier track
• One wheel stop
• Push button Remote Control
• Industrial Grade Nylon Rollers

Prices Do Not Include Installation or Shipping. 

Prices subject to change without notice. Click Here to see a complete Price List and Return Policy